Ravinder_Tomcat220T
01-10-10, 11:02 PM
Just thought I would put some specs up of my vvc as I have never put them up.
Got the coupe back in January 2004 when I was forced to get a car after my dad took the Corsa back after we had a row. (Not immature at all) :lol:
My mate told me that one of his mates was selling this car. I didn't know anything about the Rover coupe at all at this point. Just saw it, drove it, thought it was pure fast man! (Step up from a 1.2 Corsa) Liked the look of it so bought it.
She had done just 37k when I got it, now done 108k.
It's a 98' S plate, one of the last ones I believe.
I use it as my daily commuter to work etc and it has served me well over the years. In Feb 2006, the cambelt went after it skipped a tooth and caused a fair bit of damage. Got this repaired at a cost but was solid then at 100k the head gasket was going so got this sorted back in Dec 09. The guy that did it pointed out that the timing was out by half a tooth. Since I got it back it's been running better then ever. Much quicker then it was before.
Has air con (but doesn't work)
Rover coupe 1.8VVC
In BRG (Later HAM)
108k
Full sandstone leather interior (Had half leather previously but swapped it)
Kenwood headunit
Focal front components
Kenwood rear components
10" Active sub
Closed induction filter
Cat back exhaust system with 4" slash cut tailpipe (Chav can)
Standard 15" alloys
Smoked rear lights
The main letdown on the car is the bodywork. It was mint when I first bought it but it had been neglected a bit on my part. Both rear arches have rusted and there's a little rust near the doors at the bottom and the black panel between the glass panels on the roof and the windscreenis rusted quite badly. And I have some laquer peel above passenger door pillar.
Got loads of bits sorted on it recently. Just mainly niggly things but also for MOT as this is due this weekend!
Recently got a new bonnet and grille to replace the old creased one and the old one was really badly chipped. new one is immaculate compared to old one apart from a few light scratches.
Also got replacement drivers side door as the old one was very badly keyed down to the bare metal and had some rust on it.
New passenger side seal
New wing mirrors
Heater resistor just been replaced as heaters stopped working on 1 and 2. This is my 3rd one!
ABS fuse put back in as I had no abs and the light was stuck on.
New bonnet holder
New front discs and pads (still s*** brakes) not quite sure why though.
Fitted TF mirror with led lights and fitted led lights to interior light (Wow! what a difference! Whole car lights up)
Replaced seat belt thing drivers side, as my seatbelt would not click in.
New wiper motor as old one was sticking quite high on the windscreen.
Sealed vents in boot and sealed roof panels. No more leaks for the first time in years! :D
Replaced passenger side door handle. (1st one to go on this side. Been through 3 on the drivers side!)
Track rod ends replaced
New spark plugs
Now things to be done in the next 1 month (By end of Oct 2010)
Replace fuel filter
New leads
New PAS and alternator belts
Oil change/filter
282 calipers to be cleaned and painted and then fitted with ebc discs and black diamond predator pads
262 rear calipers off zr160 to be cleaned and painted too and fitted
New 17" alloys (you'll recognise them :wink: off a forum member)
Koni yellow shocks and pi springs all round
Replace cam seal as it has started leaking in the last month or so :(
Change power steering fluid
Ducting for cold air filter as I currently don't have one! Still sounds nice though under high revs.
Fix the damn rear demistor as it ain't working.
Future plans:
Possibly new exhaust system as mine has seen better days
Possibly 270 cams
Janspeed 4-2-1 manifold and downpipe
Front polybushes
Front top strut brace and maybe rear one and lower rear
Sort out bodywork but expensive job! :(
I'd like to get the air con working again.
I think that is all for now. The bodywork is my main worry.
Got the coupe back in January 2004 when I was forced to get a car after my dad took the Corsa back after we had a row. (Not immature at all) :lol:
My mate told me that one of his mates was selling this car. I didn't know anything about the Rover coupe at all at this point. Just saw it, drove it, thought it was pure fast man! (Step up from a 1.2 Corsa) Liked the look of it so bought it.
She had done just 37k when I got it, now done 108k.
It's a 98' S plate, one of the last ones I believe.
I use it as my daily commuter to work etc and it has served me well over the years. In Feb 2006, the cambelt went after it skipped a tooth and caused a fair bit of damage. Got this repaired at a cost but was solid then at 100k the head gasket was going so got this sorted back in Dec 09. The guy that did it pointed out that the timing was out by half a tooth. Since I got it back it's been running better then ever. Much quicker then it was before.
Has air con (but doesn't work)
Rover coupe 1.8VVC
In BRG (Later HAM)
108k
Full sandstone leather interior (Had half leather previously but swapped it)
Kenwood headunit
Focal front components
Kenwood rear components
10" Active sub
Closed induction filter
Cat back exhaust system with 4" slash cut tailpipe (Chav can)
Standard 15" alloys
Smoked rear lights
The main letdown on the car is the bodywork. It was mint when I first bought it but it had been neglected a bit on my part. Both rear arches have rusted and there's a little rust near the doors at the bottom and the black panel between the glass panels on the roof and the windscreenis rusted quite badly. And I have some laquer peel above passenger door pillar.
Got loads of bits sorted on it recently. Just mainly niggly things but also for MOT as this is due this weekend!
Recently got a new bonnet and grille to replace the old creased one and the old one was really badly chipped. new one is immaculate compared to old one apart from a few light scratches.
Also got replacement drivers side door as the old one was very badly keyed down to the bare metal and had some rust on it.
New passenger side seal
New wing mirrors
Heater resistor just been replaced as heaters stopped working on 1 and 2. This is my 3rd one!
ABS fuse put back in as I had no abs and the light was stuck on.
New bonnet holder
New front discs and pads (still s*** brakes) not quite sure why though.
Fitted TF mirror with led lights and fitted led lights to interior light (Wow! what a difference! Whole car lights up)
Replaced seat belt thing drivers side, as my seatbelt would not click in.
New wiper motor as old one was sticking quite high on the windscreen.
Sealed vents in boot and sealed roof panels. No more leaks for the first time in years! :D
Replaced passenger side door handle. (1st one to go on this side. Been through 3 on the drivers side!)
Track rod ends replaced
New spark plugs
Now things to be done in the next 1 month (By end of Oct 2010)
Replace fuel filter
New leads
New PAS and alternator belts
Oil change/filter
282 calipers to be cleaned and painted and then fitted with ebc discs and black diamond predator pads
262 rear calipers off zr160 to be cleaned and painted too and fitted
New 17" alloys (you'll recognise them :wink: off a forum member)
Koni yellow shocks and pi springs all round
Replace cam seal as it has started leaking in the last month or so :(
Change power steering fluid
Ducting for cold air filter as I currently don't have one! Still sounds nice though under high revs.
Fix the damn rear demistor as it ain't working.
Future plans:
Possibly new exhaust system as mine has seen better days
Possibly 270 cams
Janspeed 4-2-1 manifold and downpipe
Front polybushes
Front top strut brace and maybe rear one and lower rear
Sort out bodywork but expensive job! :(
I'd like to get the air con working again.
I think that is all for now. The bodywork is my main worry.