VIS indicator Kits.
Right I should have 10 of these made up ready for dispatch by the end of the week. They are going to come with Red and Green LEDs. Rather than the blue pictured.
The Kit consists of:This kit requires you to splice into the loom for the VIS motors, splicing and soldering onto 5 colourcoded wires that will all be explained in the instructions included. http://i76.photobucket.com/albums/j1...d/VISbuild.jpg http://i76.photobucket.com/albums/j1.../Visbuild2.jpg They will come at a cost of ?30 inc postage. I would also be greatful if the switch blank the kit replaces can be sent back to me allowing more to be produced. ( I will include a stamped addressed envelope :)) I wont be taking payment until they are ready to go. If those intrested could add their name to the list: 1. haGGard (neil) -------SENT 2. Smokey (Blair) -------SENT 3. Daytona365 --------- Pm sent 4. Wullie zs-180 --------SENT 5. Gavspav ------------SENT 6. Midcuk ------------- PAID 7. Blobslosak ---------- SENT(VIS+MIL) 8. *Taken* SENT Big thanks to Murray for suppling the switch blanks :) If anyone is in a scrap yard in the near future the blanks would be much appreciated. The Kits Ive provided I have labelled the LEDs to show which relate to which motor with masking tape. Although for future reference if you look at the back of the kit, the LEDs on the same side as the lug thats on the connector are the connected to the power motor. If installed the right way round it should appear/opperate as below :) http://i76.photobucket.com/albums/j1...ationguide.jpg |
I'll put my name down down for one, but does this fit to the left of steering wheel? (where the fog switches are) As i've got fog light switches there...
|
Quote:
A pic of one of Kevs fitted: http://i63.photobucket.com/albums/h1...cture005-2.jpg |
In that case!
1. haGGard (neil) 2. 3. 4. 5. 6. 7. 8. 9. 10. |
Just to say that I got one of these from Jay and the build quality was excellent.
|
Ive forgot, how you said they work now (LOL) I think I wanted a set, cant remember, must be the alzeimers..............
|
Quote:
Basically they tap into the feed from the motors and light one of 2 LEDs Red = Motor is shut, Green = Open. (one set for power one for balance motors.) It will let you know wether the motors actuators are open or shut, which can inform you of a fault with the VIS valves. Common cause of low powered 180s. At idle you should have 2 LED's on (one for each motor/ Red). Plant it and BOTH LED's should swap to green. At about 3krpm's the 1st LED should go back to red, at 4krpm's the 2nd LED should go back to red. If either LED isn't switching it indicates that the retrospective motor is broken. :) |
I remember now, and i have found the origional thread. Put me down for one.........
1. haGGard (neil) 2. Smokey (Blair) 3. Daytona365 (Gordon) 4. 5. 6. 7. 8. 9. 10. |
1. haGGard (neil)
2. Smokey (Blair) 3. Daytona365 4. 5. 6. 7. 8. 9. 10. Didnt realise you had been entrusted with such powers smokey ;) |
;)
|
put me down please
pm sent |
me too please. Assuming I'll have no major problems with LHD? Oh, and you don't need to send me a SAE unless you've got some german stamps........
|
If those intrested could add their name to the list:
1. haGGard (neil) 2. Smokey (Blair) 3. Daytona365 4. Wullie zs-180 5. Gavspav 6. 7. 8. 9. 10. *Taken* |
If those intrested could add their name to the list:
1. haGGard (neil) 2. Smokey (Blair) 3. Daytona365 4. Wullie zs-180 5. Gavspav 6. Midcuk 7. 8. 9. 10. *Taken |
Sorry for the delay on these have been in bed unwell the last few days.
Although I will be ready to post by saturday if not monday Those with their names down will be recieving a pm soon with payment details |
Yes please, the kick at 3k has gone so this will no doubt confirm my worst fears.
If those intrested could add their name to the list: 1. haGGard (neil) 2. Smokey (Blair) 3. Daytona365 4. Wullie zs-180 5. Gavspav 6. Midcuk 7. Blobslosak 8. 9. 10. *Taken |
ooo, are you still doing the MIL kits too?? MOT times soon, then VIS is getting fixed, induction fitted and cat decatted as I fancy some more speed :)
p.s. hope you feel better soon. |
Quote:
|
1. haGGard (neil) ------- Pm sent PAID
2. Smokey (Blair) ------- Pm Sent 3. Daytona365 --------- Pm sent 4. Wullie zs-180 -------- Pm sent 5. Gavspav ------------ Pm sent 6. Midcuk ------------- Pm sent 7. Blobslosak ----------- Pm sent 8. 9. 10. *Taken |
1. haGGard (neil) ------- Pm sent PAID Will be sent monday
2. Smokey (Blair) ------- Pm Sent -----Will be sent monday 3. Daytona365 --------- Pm sent 4. Wullie zs-180 -------- Pm sent PAID Will be sent monday 5. Gavspav ------------ Pm sent PAID Will be sent monday 6. Midcuk ------------- Pm sent 7. Blobslosak ----------- Pm sent PAID Will be sent monday (VIS+MIL) 8. 9. 10. *Taken* Will be sent monday |
1. haGGard (neil) -------SENT
2. Smokey (Blair) -------SENT 3. Daytona365 --------- Pm sent 4. Wullie zs-180 --------SENT 5. Gavspav ------------SENT 6. Midcuk ------------- PAID 7. Blobslosak ---------- SENT(VIS+MIL) 8. *Taken* SENT Will be doing a write up to fully explain the Indicators, so people know exactly how they show work when the VIS are fully operational :) |
Have updated post #1 with a diagram of how the Indicators work if the VIS motors are fully functional :)
|
got them on tuesday all fitted just the wiring part to do wish me luck:book::yikes::wall::wall::wall:
|
Good luck, one thing that I missed in the instructions, there appear to be 2 black wires in the loom, either will do its only the negative return to battery :)
|
Jay, it's good of you to spend your own time sorting out the vis indicators for peeps.
Well Done mate!! :mbounce: |
thanx its done only thing is started the engine after fitting and the left green has come on and none of the rest not reved it or took it a run yet though
any ideas? |
Quote:
At idle both red lights should be on. A rev should put both reds out and both greens on. If a green is on at idle, it could be wired up incorrectly, or one of the motors is stuck closed. |
Sounds like the kits are a sucess, cant wait to send you my cash so I can fit mine............Roll on pay day................
Can sit there in traffic making the lights change colour lol......:construction: |
Quote:
|
I have it all fitted, great kit, thanks :) and I'm 99% sure I've wired it correctly, and I'm 100% sure I have a VIS issue as I have no kick at 3k and it rattles like a bag of spanners. Anyway, this is what my lights say....
////red green green red idle: on on off on <3k: off on off off (i.e. plant my foot) 3k : on on off off 4.3k: on on off on Hmmm, would appear to have issues with both motors??? reds work as they should but have one motor with the green light always on and the other always off. Any advise? Cheers. |
Quote:
http://forums.xpowerforums.com/showt...ght=vis+repair |
Quote:
These VIS indicators are fantastic bits of kit. |
Quote:
|
Quote:
|
Quote:
|
Quote:
|
Sorry yeah, power motor.
|
Quote:
double and tripple checked the wiring and is ok :cry::cry::cry: |
Quote:
Warm the unit with a hair dryer to soften up the seal, prise the lugs round the casing gently and prise up all round, it will come just go easy at it:) |
All these flashing lights.............cant wait to get paid so i can tell you all what happens with my set..........
|
All times are GMT. The time now is 12:27 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ? 2010 theMGZS.co.uk