theMGZS.co.uk  :: MG ZS forum

theMGZS.co.uk :: MG ZS forum (https://www.themgzs.co.uk/vb/index.php)
-   General Discussion (https://www.themgzs.co.uk/vb/forumdisplay.php?f=14)
-   -   KV6 Water in Engine - Help! (https://www.themgzs.co.uk/vb/showthread.php?t=15657)

silver bullet 05-02-11 10:45 AM

KV6 Water in Engine - Help!
 
So we had some bad weather and due to my daily car having to be leant to a family member I had to take the ZS to work. I got stuck on a small road which had water running across, It wasnt all that deep, i was slowly (1st gear) going through it and it was up to the lip on the front bumper, then all of a sudden the car died about half way across (15 metres in approx). a quick check shows that the air filter has sucked water up, the engine wont even tick over now. have checked spark plugs and they seem fine but there is water at end of dipstick. So has anyone had this problem and what should i do/check now? I am half expecting to need to change engines but thought id ask before giving up all hope. I am thinking if i had put an aftermarket pod filter on i wouldnt of had this problem!

Any advice would be great!

fastmike 05-02-11 11:02 AM

Change the contaminated oil...... get the car running and drive it for a good few (20 maybe) miles to clear any water out . .... Your Lamba sensor will be contaminated ( is the mil light on?) See if that improves matters...Worse case senario your engine hydraulic locked and bent a con rod or two ...... I,ve even known cylinder liners to crack cos of hydraulic lock

andys1981 05-02-11 11:46 AM

sounds like its hydralocked buddy

Ritchy 05-02-11 11:46 AM

take all the spark plugs out and spin it over so all the water pumps out the cylinders, if it was low speed might be okay and not done any damage, then change you oil and try start it with plugs in

Alan.F 05-02-11 05:07 PM

driving through standing water is the biggest killer of KV6 engines unfortunately

silver bullet 05-02-11 09:18 PM

Quote:

Originally Posted by ritchyp (Post 193753)
take all the spark plugs out and spin it over so all the water pumps out the cylinders, if it was low speed might be okay and not done any damage, then change you oil and try start it with plugs in

Yep tried this

silver bullet 05-02-11 09:19 PM

Quote:

Originally Posted by fastmike (Post 193747)
Change the contaminated oil...... get the car running and drive it for a good few (20 maybe) miles to clear any water out . .... Your Lamba sensor will be contaminated ( is the mil light on?) See if that improves matters...Worse case senario your engine hydraulic locked and bent a con rod or two ...... I,ve even known cylinder liners to crack cos of hydraulic lock

Yeah I suspect it may have done a liner, no external oil so it hasnt put a rod through. I suspect it was hydraulic lock, looks like my fears have been confirmed! Cheers guys

silver bullet 05-02-11 09:35 PM

Quote:

Originally Posted by fastmike (Post 193747)
.... Your Lamba sensor will be contaminated ( is the mil light on?) See if that improves matters

Excuse the stupid questions but what is a mil light?

grimmy 05-02-11 10:00 PM

Malfunction indicator light .yellow engine shaped light in the top left of the dashboard I know, fed up seeing the bloody thing over the years.

greenyzs180 05-02-11 10:14 PM

sorry to hear whats happened but my dad went through a load of water at slow speed and it blew the engine,was in a crappy escort must say but i try to avoid ever doin this,hope sorts out anyway


All times are GMT. The time now is 01:59 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ? 2010 theMGZS.co.uk