|
|
19-05-12, 08:53 PM
|
#1
|
Member
Join Date: Jun 2011
Location: Great Yarmouth
Posts: 933
|
In need of some help!
I recently had my nsr caliper replaced at my local friendly garage as it was knackered. I had the discs and pads done too while it was in, so all sliders etc should of been greased as they told me they had, but now the osr caliper has seized. When they did the other caliper they did say the other one would probably follow suit at some point in the near future.
I am just wondering how easy it is to change it myself as I am not paying out 75 quid for the part plus the labour and all just before the MOT as well.
Before anyone says, the local scrappie hasn't got any and I can't get any second hand ones off ebay as I have to use the car again for work on Tuesday night and it wouldn't arrive in time.
I am really worried as I don't want to bake the pads and/or warp the discs as that's what happened on the other side last time.
Any suggestions, or any how 2's knocking about??
Thanks people!!
|
|
|
19-05-12, 09:05 PM
|
#2
|
Member
Join Date: Feb 2008
Location: UK
Posts: 10,493
|
Don't know of a how to but they aren't difficult.
Eurocarparts are good for replacment calipers, about £50 each exchange.
__________________
Former custodian of the legend that was FE54 - RIP
|
|
|
19-05-12, 09:20 PM
|
#3
|
Member
Join Date: Nov 2009
Location: Spalding Lincs
Posts: 1,344
|
Very easy, are you just freeing up the sliders ?
12+14mm spanner and a philips screwdriver for the disk screws.
Jack the car up and take the wheel of. Undo the two philips screws (they may need drilling out) undo the two bolts on the slider with the 12mm spanner. Lever the caliper of. If you can pull the pins out do so and clean and grease them up. (dont take the rubber dust guards out of the carrier they are not easy to get back in). If not undo the two bolts holding the carrier to the hub so you can do it on the bench.
Wind the piston back in clock wise with a flat bar, just a little to put it back to gether.
I think you are a little to far away but I would be happy to do it for you
Last edited by big_wasa; 20-05-12 at 07:30 AM.
|
|
|
19-05-12, 10:30 PM
|
#4
|
Member
Join Date: Oct 2010
Location: Sunny Norfolk
Posts: 478
|
Good ol Norfolk us boys!!! Loely coastal erosion to help us allong on our way,,,,
__________________
Monogram Typhoon 180 - 62k and in need of rear end repair
|
|
|
19-05-12, 10:33 PM
|
#5
|
Member
Join Date: Jun 2011
Location: Great Yarmouth
Posts: 933
|
Quote:
Originally Posted by James Raby
Good ol Norfolk us boys!!! Loely coastal erosion to help us allong on our way,,,,
|
Yeah tell me about it mate, damn sea air!!
|
|
|
19-05-12, 10:32 PM
|
#6
|
Member
Join Date: Jun 2011
Location: Great Yarmouth
Posts: 933
|
Quote:
Originally Posted by talkingcars
Don't know of a how to but they aren't difficult.
Eurocarparts are good for replacment calipers, about £50 each exchange.
|
I did look on their website but the prices were quite high for the rears, but I think there is a new ish branch opened in Norwich so do some investigating into that one cheers!
Quote:
Originally Posted by big_wasa
Very easy, are you just freeing up the sliders ?
12+14mm spanner and a philips screwdriver for the disk screws.
Jack the car up and take the wheel of. Undo the two philips screws (they may need drilling out) undo the two bolts on the slider with the 12mm spanner. Lever the caliper of. If you can pull the pins out do so and clean and grease them up. (dont take the rubber dust guards out of the carrier they are not easy to get back in). If not undo the two bolts holding the caliper to the hub so you can do it on the bench.
Wind the piston back in clock wise with a flat bar, just a little to put it back to gether.
I think you are a little to far away but I would be happy to do it for you
|
I will have a look at the caliper tomorrow or Monday, but they are new slider bolts on there. I think it's the caliper itself but I will know more upon inspection. I am not sure about how to go about getting the spring from the handbrake off. Do I just loosen it from the nut inside the car then unclip the spring on the caliper. There is a couple of scrappies near Norwich so might be worth giving them a try but the chances of them having a 180 osr calliper are quite slim I think.
Thanks for the offer, it always seems to be that hardly anybody is from around here.
|
|
|
19-05-12, 10:40 PM
|
#7
|
its ginger its phenomenal
Join Date: Jul 2007
Location: Cumbertoon
Posts: 8,141
|
Most likely not the caliper,it is most likely the pads will be sticking in the carrier,do as was said above and strip the sliders out and re grease but on refitting file some material from the top and bottom edges of the pads where they contact the shims in the carrier they stick all the time causing issues as well its overlooked a lot when people do the back brakes on the Zs.
__________________
<iframe src="http://gamercard.xbox.com/grimmy1973.card" [="" sigpic]=""></iframe>
|
|
|
19-05-12, 10:44 PM
|
#8
|
Member
Join Date: Jun 2011
Location: Great Yarmouth
Posts: 933
|
Thanks Grimmy, I'll have a good look as soon as I get a chance!
|
|
|
20-05-12, 07:12 AM
|
#9
|
Member
Join Date: Feb 2012
Location: Near Newquay
Posts: 654
|
You may find that there is lots of corrosion under the top and bottom shims that pinches the pads as described!! I tend to simply remove the lower shim as and the brakes work much better as a result!! They only serve to stop the pads rattling in the caliper anyway but tbh I've never heard them rattle without them !!
__________________
Ex ZS180 Owner and fan.
|
|
|
20-05-12, 07:39 AM
|
#10
|
Member
Join Date: Nov 2009
Location: Spalding Lincs
Posts: 1,344
|
As above I doubt its the caliper itself. It will be the slider pins or sticking pads.
The new bolts that come with the pads just hold the caliper to the carrier on the sliding pins.
If your changing the whole caliper. Then there is a pin with an R clip and a big C clip holding the hand brake cable to the caliper and thats it. The Bracket does not come with a recon caliper so that needs to swaped aswell. Just two bolts.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT. The time now is 08:33 AM.
|